Squirts

310g aerosol

Squirts is a high quality, quick drying acrylic enamel spray paint ideal for many projects around the home. Squirts is easy to use and creates a smooth, glossy professional finish on almost any surface.

Ideal for use on canvas, cupboards, gates, doors, letterboxes, trim, fixtures, furniture, toys, wicker or craft projects.

Features:

  • Paint and primer in one
  • Bonds to plastic, wood, metal and more
  • Quick drying - Touch dry in 10 minutes
  • Excellent coverage - 3.5m2
  • Wide palette of colours
  • Hard wearing
  • Interior and exterior application
  • Safe to spray - CFC and lead free
  • Non chroming formula

Suitable Surfaces

Squirts may be used on most surfaces including timber, metal, wicker, masonry, plastic and ceramic.

Safety & First Aid

DANGER

  • KEEP OUT OF REACH OF CHILDREN
  • Read label before use

EXTREMELY FLAMMABLE AEROSOL. KEEP AWAY FROM HEAT, HOT SURFACES, SPARKS, OPEN FLAMES AND OTHER IGNITION SOURCES. CAUSES SERIOUS EYE IRRITATION. MAY CAUSE DROWSINESS OR DIZZINESS.

  • Wear eye or face protection.
  • Do not breathe dust or mist.
  • Get medical attention if you feel unwell.
  • IF IN EYES: Rinse cautiously with water for several minutes. IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for
  • eathing. Immediately call a POISON CENTRE or physician.
  • If medical advice is needed, have product container or label at hand.
  • Protect from sunlight.
  • Do not expose to temperatures exceeding 50°C.
  • Pressurised container: Do not pierce, burn or strike on hard surfaces, even after use.

For 24 hour medical emergency response in Australia call 1800 883 254 and in New Zealand call 0800 000 096.

Caution

HIGHLY FLAMMABLE. Keep can away from flame and heat and eliminate any source of ignition. Keep can in a cool place and out of sun. Contents of can under pressure. Do not puncture or incinerate the can, even when empty.

Environment

  • Dispose of contents and container in accordance with all local, regional, national and international regulations.
  • Empty aerosol cans are recyclable via steel can recycling programs.
  • Important: Deliberate misuse of this product to damage public or private property is a crime.

Preparation

  • The surface must be clean, dry and free from dust, dirt, grease, oil, rust scale and other contaminants. For best results on new plastic, thoroughly clean the surface with White Knight Rust Guard Solvent.
  • Sand previously painted or glossy surfaces with 600# abrasive paper.
  • For optimal performance, prime timber and bare ferrous metal (e.g. steel) with White Knight Rust Guard All Purpose Primer, and galvanised iron and non-ferrous metal (e.g. aluminium) with White Knight Rust Guard SLS Etch Primer.
  • Undercoat with White Knight Squirts Undercoat to achieve a clean, bright finish, particularly when coating dark surfaces.
  • Cover surrounding areas to protect from overspray.
  • Test spray first on a small inconspicuous area to ensure surface compatibility.

Application

  1. Shake can vigorously for 1 minute (after the ball begins to rattle) before use and regularly during use.
  2. To achieve an even coating, hold the can upright approximately 15-20cm from the surface.
  3. Press button firmly and spray with a smooth sweeping motion. To achieve the best results, apply several light coats rather than one heavy coat, overlapping each spray pass. To prevent paint sagging, avoid spraying too close to the surface or spraying too heavily.
  4. Repeat if necessary.

Do not use at temperatures below 15°C, above 30°C or in high humidity.

Coverage

Approximately 3.5m² per can.

Drying

Touch dry in 10 minutes.

Re-coat after 1 hour.

Maximum adhesion on plastic will be achieved after 7 days.

Drying will be slower in cold or humid conditions, in the absence of ventilation or where a heavy film build is applied.

* Adhesion to some plastics may be difficult to achieve due to the ever increasing variety of plastic compositions being created - it is recommended that adhesion is tested on an inconspicuous area first.

Clean Up

After use, to prevent nozzle blocking, turn can upside down and press button until only gas escapes. Overspray can be removed while still wet with White Knight Rust Guard Solvent or mineral turps.

FIND A STORE
Squirts
Safe to Spray
Hints and Tips
  • Paint will not adhere to glossy or dirty surfaces.
  • Use a drop sheet to cover objects from overspray. Overspray can travel long distances so make sure you cover a wide area.If possible, place the object to be sprayed inside a cardboard box or on newspaper.
  • When spraying, spray across object, starting and finishing off to the side. It is better to spray a few light coats than one heavy coat.
  • Practice makes perfect. Do a test piece first on cardboard to get the feeling.
  • Use masking tape or newspaper to prevent paint from going on areas you don't want it to.
  • Have lots of rags handy for any cleaning.